TPE Granules for Overmoulding: A Buyer’s Checklist for Grips and Handles

When sourcing TPE granules for an overmoulded grip or handle, identify the rigid substrate first. Then describe the target hardness, surface feel, part geometry and moulding process. Those details give the supplier a useful starting point for discussing a grade and planning a sample evaluation.

Haishengda’s existing TPE granules page covers flexible-part requirements and overmoulding discussions. This checklist helps buyers prepare an enquiry without changing the product design or assuming that one TPE grade suits every substrate.

Name the substrate, including its grade

Identify the material that the TPE will be moulded onto. Include its supplier and grade designation if known, plus any relevant filled, coloured or modified version. A broad description such as “plastic handle” leaves an important question unresolved.

TPE selection for overmoulding depends on the material combination. Avient’s TPE-selection guide organizes its own overmoulding grades by substrate rather than treating them as interchangeable. Use that principle when preparing an enquiry: name the substrate and ask about the proposed TPE grade for that combination.

Describe how the grip should feel and work

List the properties the customer will judge on the finished part. These may include target hardness, grip feel, appearance and colour. Where possible, provide a physical reference or clearly labelled photographs so purchasing, design and production teams are discussing the same target.

Hardness is one part of that brief. A surface impression, a drawing and a description of the intended use give additional context. Keep the approved sample identification with the project records instead of relying on the word “soft” to describe the final requirement.

Share the geometry and moulding route

Provide a drawing showing the TPE-covered area, layer thickness, edges and the underlying substrate. Tell the supplier whether the process uses pre-moulded inserts or a two-shot arrangement, and identify any design or tooling details that are already fixed.

Material choice is only part of the bonding discussion. A KRAIBURG TPE product data sheet, for example, states that adhesion quality also depends on mould design, product geometry and process parameters. That is a reason to evaluate the actual material and part combination rather than assume an untested grip will perform like a different design.

Plan a documented trial

Before ordering trial material, agree what the evaluation should answer. Separate appearance and feel from the way the TPE remains attached to the substrate. Define the checks that matter for the intended part, who will review the results and which sample will be retained as a reference.

Record the TPE grade, substrate grade, relevant production settings and observed result for each trial. Include photographs of defects and note whether an issue appears consistently or only under particular conditions.

For grade-specific drying and processing guidance, use the proposed material’s technical information. Avient’s overmoulding processing guide identifies moisture, substrate condition, processing conditions and part design among factors affecting adhesion. Its guidance also directs users to the individual grade data sheet. A general web article is not a substitute for the settings recommended for the material being evaluated.

Prepare one enquiry that purchasing and engineering can both use

Include these items in the request:

  • Finished-part drawing or photographs and its intended use.
  • Exact substrate material and grade, when available.
  • Target hardness, colour, finish and reference sample.
  • Moulding route and the requirements to evaluate during trials.
  • Required documents and destination market.
  • Trial quantity, expected purchasing volume and delivery destination.

This format helps keep the engineering question and the commercial quotation connected. It also makes quotations easier to compare because suppliers receive the same project brief.

For TPE granule enquiries, discuss these supply options with Haishengda:

  • Hardness: Shore A 20–100, with customisation supported.
  • Minimum order quantity: 1 metric tonne.
  • Packaging: 25 kg per bag.
  • Trial samples: available before ordering.
  • Domestic lead time: 3–5 days.
  • Overseas delivery: schedule agreed according to the destination country.

Questions buyers ask

Will a TPE grade bond to every rigid plastic?

Treat bonding as a question about the specific grade and substrate combination. Provide the substrate identification and evaluate samples using the intended design and process.

What hardness range can I discuss with Haishengda?

Haishengda supports customised TPE hardness within Shore A 20–100. Include the target hardness and desired feel, together with the substrate identification and part drawing. This is a hardness range, not a service-temperature rating or a guarantee of adhesion to the substrate.

Can I request samples before placing a production order?

Yes. Trial samples are available. Send the application, substrate information and sample requirements through the enquiry form so the next discussion can focus on the proposed evaluation.

Discuss your TPE project

Start with the existing TPE granules range. Send your project brief through the enquiry form or WhatsApp. You can also view Haishengda’s other existing plastic-granule products when reviewing a broader sourcing requirement.

Send your material requirements

Scroll to Top