Short answer: “Non-marking” is a test requirement, not a property that can be confirmed by the name TPR alone. Tell the supplier which surface the finished grip touches, whether you mean colour transfer, staining after contact, or a visible scuff, and how the sample will be pressed, moved, cleaned and inspected. Then test the proposed compound in the actual colour and moulded geometry against a written pass/fail rule.
This article addresses one narrow question: how to make a non-marking requirement testable. For general grip hardness, feel, finish and sourcing questions, see our earlier TPR guide for footwear and grips. You can also review the existing TPR granules page before sending an enquiry.
First define what “mark” means in your project
Buyers may use one word for several different outcomes. A dark residue on a white panel after sliding contact is not the same as staining that develops after prolonged stationary contact. A visible line may also come from abrasion of the panel rather than transfer from the grip. Ask the product team which outcome matters and photograph an unacceptable example if one exists.
For contact staining, ASTM D925-14(2025) describes methods for evaluating staining of surfaces by rubber compounds. Its public scope distinguishes contact, migration and diffusion staining and cautions that laboratory results need not reproduce natural exposure. The full standard is a paid document; the buyer or test laboratory should decide whether it applies to the proposed TPR compound and end use. Do not claim compliance merely because a sample looks clean after a quick wipe.
Specify the real contact surface
Identify the counter-surface by material, finish and colour: for example, a particular painted metal panel, floor coating, plastic housing or textile. A white laboratory card may be useful for screening, but it cannot stand in for a customer's actual finish without a demonstrated correlation. Supply a reference panel from the intended production finish where possible.
Record whether the grip contacts a dry surface, an oily surface, a cleaning agent or another material. If the product is stored in contact with a painted surface, contact time and storage temperature matter. If the grip slides across a surface, pressure, movement and number of cycles matter. Keep stationary-contact and rubbing tests separate so a pass in one is not mistaken for a pass in the other.
Build a small comparison matrix
Agree on the test before selecting a grade. A practical trial sheet can include:
| Record | Buyer input |
|---|---|
| Sample | Proposed TPR grade and lot, colour, moulded-part revision and surface texture |
| Counter-surface | Material, coating, colour, supplier and finish revision |
| Exposure | Stationary contact or motion, contact force, duration, temperature and cleaning condition |
| Baseline | Unused reference panel and photos under fixed lighting |
| Inspection | When to inspect, whether to wipe, how to record residue, stain, scuff or colour change |
| Acceptance | A written visual or measured limit and who makes the final decision |
For an early screen, compare at least the current material and candidate on the same type of panel under the same conditions. Retain the untreated panel as a control. If the candidate passes, repeat with the intended moulded part and production colour. The buyer's engineer or laboratory should choose any formal test method and sample count required by the application; the table above is a planning aid, not a substitute for a standard.
Do not separate the colour from the compound
The final grip may use pigments, additives and a surface texture that differ from a clear or uncoloured trial plaque. Ask whether the reported result covers the actual formulation, colour and process. Note the moulding settings and sample age so a second run is comparable. If a supplier offers several hardness options, test the options that meet the grip's mechanical and feel requirements, rather than assuming that a hardness number predicts marking.
If the first test leaves a mark, record the exact mode of failure. A removable colour transfer, a permanent stain and damage to the counter-surface lead to different material or design questions. Do not describe a failed sample simply as “not non-marking”; the more precise record helps the next trial.
Common buyer questions
Is there a universal non-marking TPR grade?
No universal claim follows from the material family name. Suitability depends on the compound, colour, moulded surface and the specific contact surface and conditions. Ask for grade-specific evidence and validate the finished application.
Can a one-minute hand rub replace a laboratory test?
It can flag an obvious issue, but it does not reproduce a defined contact force, duration, temperature or counter-surface. Use it as a screen, then agree on a repeatable test and acceptance rule.
What should we send for a sample request?
Send the part drawing, colour and hardness target, actual counter-surface, contact or rubbing conditions, an example of an unacceptable mark, required test method if one is specified, sample quantity and destination. State unknowns openly.
Use the contact form or WhatsApp to discuss a TPR sampling trial. Haishengda can review the requirement against its existing TPR range; a “non-marking” result should be confirmed on the proposed grade and finished part under the agreed conditions.